MiTAC PH10LU Instrukcja Użytkownika

MITAC Desktop Board PH10LU Product Guide

10 Internal SPDIF header Figure 5 Internal SPDIF header pin-out diagram Pin Signal name Description 1 GND Ground 2 SPDIF_OUT SPDIF

11 Parallel port header Figure 7 Parallel port header pin-out Pin Standard Signal Name ECP Signal Name EPP Signal Name 1 STROBE# ST

12 Serial port header Figure 8 Serial port header pin-out Pin Signal Pin Signal 1 DCD (Data Carrier Detect) 2 RXD# (Receive Data) 3 T

13 9 IntA_P1_D+ USB3 ICC Port1 D- (USB2 Signal D+) 10 ID Over Current Protection 11 IntA_P2_D+ USB3 ICC Port2 D+ (USB2 Signal D+) 12 IntA_P

14 Front/Rear fan header Figure 11: Front/Rear fan header TABLE 11: PROCESSOR FAN HEADER LVDS panel voltage selection header

15 Pin Signal Name 1 NC 2 VCC3/3V 3 12V 4 LCD SEL PWR 5 NC 6 VCC/5V TABLE 12: LVDS PANEL VOLTAGE SELECTION HEADER Inverter power voltage s

16 LVDS Pin Signal Name Description 1 BKLT_EN Backlight enable 2 BKLT_PWM Backlight PWM control 3 5V/12V Inverter power 4 5V/12V Inverter pow

17 27 LA_CLKN LVDS Channel A diff data output - negative 28 GND Ground 29 GND Ground 30 GND Ground 31 EDID_CLK EDID/DDC clock signal 32 BKLT_

18 RJ45 LED Behavior Diagram LED Color State Condition Link N/A Off LAN link is not established Green On LAN link is established Blinking L

19 MITAC Desktop Board PH10LU BIOS Specifiction

2 Desktop Board Features This chapter briefly describes the features of Desktop Board PH10LU. Table 1 summarizes the major features of the Des

20 GENERAL OVERVIEW This document specifies the BIOS requirements for PH10LU Note: The BIOS specification may be changed depend on hardware design

21 - Chassis Intrusion Header x1 - Audio Header (Front Panel Mic / Hp) - S/PDIF Out Audio Header - 4-pin CPU Fan Header - 4-pin Front Fan Hea

22 Management Engine Specification : 493796_493796_Revision_1p2_ME9_0_5MB.pdf Super I/O Specification : NCT6104D_Datasheet_v1_5.pdf Others

23 initialized, control is transferred to the INT 19h Bootstrap Loader, to load the available operating system on the disk. During the POST period

24 Power Button In ACPI mode, Power Button switches the system from the sleeping/soft off state to the working state, and signals the OS to transi

25 Version (String2) - " " Serial Number (String3) - " " Asset Tag Number (String4) - " " Boot-up State: 0x

26 Send Release Note for each BIOS release. Release Note contains added features, fixed issues & known restriction. BIOS RELEASE FTP Server P

27 MAINTENANCE Support new function and new OS in nearly future as many as possible Support simple changing from our customer’s BIOS requests. For

28 0x2 AP initialization before microcode loading 0x3 North Bridge initialization before microcode loading 0x4 South Bridge i

29 0x36 CPU post-memory initialization. System Management Mode (SMM) initialization 0x37 Post-Memory North Bridge initialization is star

3 PCI Express* Full-Mini Card slot with Half-Mini Card support Either Option Peripheral Interfaces  USB 3.0 back panel connectors (blue) 2  US

30 Recovery Error Codes 0xF8 Recovery PPI is not available 0xF9 Recovery capsule is not found 0xFA Invalid recovery capsule 0xFB –

31 0x96 PCI Bus Assign Resources 0x97 Console Output devices connect 0x98 Console input devices connect 0x99 Super IO Initiali

32 0xD8 Invalid password 0xD9 Error loading Boot Option (LoadImage returned error) 0xDA Boot Option is failed (StartImage returned

33 Battery Caution There is insufficient space on this Desktop Board to provide instructions for replacing and disposing of the Lithium io

4 Desktop Board Components Figure 1 shows the approximate location of the major components on the top side of MiTAC Desktop Board PH10LU.

5 TABLE 2. MITAC DESKTOP BOARD PH10LU COMPONENTS (SHOWN IN FIGURE 1) A Back Panel Connectors B Parallel Port Header C LVDS Connector (Optiona

6 Processor The board supports 4th generation Intel Core processors. Other processors may be supported in the future. This board supports pro

7 Connecting to the Internal Headers and Connectors Front panel main header Figure 2 Front panel main header pin-out Pin Sig

8 Chassis Intrusion Detection Header The chassis intrusion detection header must be 1x2, 2.54mm pitch, colored black and with extended back, as

9 Pin Signal name Description 1 PORT 1L Analog Port 1 - Left channel (Microphone) 2 GND Ground 3 PORT 1R Analog Port 1 - Right channel (Micropho